华人|体彩hrcp188

                                        San Diego Plastics
                                        2220 McKinley Avenue
                                        National City  CA  91950
                                        800/925-4855   619/477-4855   FAX 619/477-4874

                                        PLASTIC MACHINING TIPS

                                        Cutter Guy

                                        General Fabrication Guidelines
                                         

                                        The following guidelines are presented for those machinists not familiar with the machining characteristics of plastics. They are intended as guidelines only, and may not represent the most optimum conditions for all parts. The troubleshooting quick reference in this section should be used to correct undesirable surface finishes or material responses during machining operations.

                                        Most quality stock shape materials are stress relieved to ensure the highest degree of machinability and dimensional stability. However, the relative softness of plastics (compared to metals) generally results in greater difficulty maintaining tight tolerances during and after machining. A good rule of thumb for tolerances of plastic parts is +/- .001 per inch of dimension although tighter tolerances are possible with very stable, reinforced materials.

                                        When machining plastic stock shapes, remember...
                                         

                                        • Thermal expansion is up to 10 times greater with plastics than metals
                                        • Plastics lose heat more slowly than metals, so avoid localized overheating
                                        • Softening (and melting) temperatures of plastics are much lower than metals
                                        • Plastics are much more elastic than metals

                                        Because of these differences, you may wish to experiment with fixtures, tool materials, angles, speeds and feed rates to obtain optimum results.

                                        Getting Started
                                         

                                        • Positive tool geometries with ground peripheries are recommended
                                        • Carbide tooling with polished top surfaces is suggested for optimum tool life and surface finish. Diamond coated or polycrystalline tooling provides optimum surface finish when machining Duratron?XP or Vespel?br> PI or Celazole* PBI.
                                        • Use adequate chip clearance to prevent clogging
                                        • Adequately support the material to restrict deflection away from the cutting tool
                                        Turning
                                        Operations require inserts with positive geometries and ground peripheries. Ground peripheries and polished top surfaces generally reduce material build-up on the insert, improving the attainable surface finish. A fine grained C-2 carbide is generally best for turning operations.

                                         

                                        Drilling
                                        The insulating characteristics of plastics require consideration during drilling operations, especially when hole depths are greater than twice the diameter.

                                        Small diameter holes (232" or 1mm to 1.0 or 25mm)
                                        High speed steel twist drills are generally sufficient for small holes. To improve swarf removal, frequent pull-out (peck drilling) is suggested. A slow spiral (low helix drill will allow for better swarf removal.

                                        Large diameter holes (1.0?or 25mm and larger)
                                        A slow spiral (low helix) drill or general purpose drill bit ground to a 118?point angle with 9?to 15?lip clearance is recommended. The lip rake should be ground (dubbed off) and the web thinned.

                                        It is generally best to drill a pilot hole (maximum 1/2?diameter) using 600 to 1,000 rpm and a positive feed of 0.005?to 0.015?per revolution. Avoid hand feeding because of the drill grabbing which can result in microcracks forming. Secondary drilling at 400 to 500 rpm at 0.008 to 0.020?per revolution is required to expand the hole to larger diameters.

                                        A two step process using both drilling and boring can be used on notch sensitive materials such as Ertalyte?PET-P, Torlon* PAI, Duratron?XP, Vespel?PI, Celazole* PBI and glass or carbon reinforced products. This minimizes heat build-up and reduces the risk of cracking.

                                        1. Drill a 1? diameter hole using an insert drill at 500 to 800 rpm with a feed rate of 0.005?to 0.015?per revolution.
                                        2. Bore the hole to final dimensions using a boring bar with carbide insert with 0.015?to 0.030?radii at 500 to 1,000 rpm and a feed rate of 0.005 to 0.010?per revolution.

                                        Threading and Tapping
                                        Threading should be done by single point using a carbide insert and taking four to five 0.001?passes at the end. Coolant usage is suggested. For tapping, use the specified drill with a two flute tap. Remember to keep the tap clean of chip build-up. Use of a coolant during tapping is also suggested.

                                        Milling
                                        Sufficient fixturing allows fast table travel and high spindle speeds when end milling plastics. When face milling, use either high positive or high shear geometry cutter bodies.

                                        Sawing
                                        Band sawing is versatile for straight, continuous curves or irregular cuts. Table saws are convenient for straight cuts and can be used to cut multiple thicknesses and thicker cross sections up to 4?with adequate horsepower. Saw blades should be selected based upon material thickness and surface finish desired.


                                         

                                        Machining Tips
                                         
                                        • Rip and combination blades with a 0?tooth rake and 3? to 10?tooth set are best for general sawing in order to reduce frictional heat.
                                        • Hollow ground circular saw blades without set will yield smooth cuts up to 3/4?thickness.
                                        • Tungsten carbide blades wear well and provide optimize surface finishes.

                                        Back to Top of Page
                                        Coolant Recommendations

                                        Coolants are generally not required for most plastic machining operations (not including drilling and parting off). However, for optimum surface finishes and close tolerances, non-aromatic, water soluble coolants are suggested. Spray mists and pressurized air are very effective means of cooling the cutting interface. General purpose petroleum based cutting fluids although suitable for metals and some plastics, may contribute to stress cracking of amorphous plastics such as Acrylic, Polycarbonate, Polysulfone, Ultem?PEI, and Radel?R PPSU.
                                        Coolants Tips
                                        • Coolants are strongly suggested during drilling operations, especially with notch sensitive materials such as Ertalyte?PET-P, Torlon?PAI, Duratron?XP, Vespel? PI, Celazole?PBI and glass or carbon reinforced products.
                                        • In addition to minimizing localized part heat- up, coolants prolong tool life. Example (flood) coolants suitable for most plastics include: A generally suitable mist coolant is Astro-Mist 2001A (Monroe Fluid Technology, Hilton, NY).

                                        Back to Top of Page

                                         
                                        FABRICATION GUIDELINES - TURNING AND DRILLING
                                        MATERIALS REL.
                                        MACHIN-
                                        ABILITY
                                        (1 to 10
                                        1=easiest)
                                        TURNING DRILLING**
                                        Depth of cut Speed
                                        Feet/Min.
                                        Feed,
                                        In./Rev.
                                        Nominal Hole Dia. Feed,
                                        In./Rev.
                                        Acetal copolymer
                                        Delrin? Delrin?AF
                                        Delrin?AF Blend
                                        Nylon 101
                                        Nylatron?GS, GSM
                                        Nylatron?GSM Blue
                                        Nylatron?NSM
                                        MC?901, MC?907 Nylon
                                        Polycarbonate
                                        Polysulfone
                                        Ultem?1000 & 2300 PEI
                                        1
                                        1
                                        1
                                        1
                                        1
                                        1
                                        1
                                        1
                                        3
                                        3
                                        7
                                        .150?br> .025? 500-600
                                        600-700
                                        .010-.015
                                        .004-.007
                                        1/16"
                                        1/8"
                                        1/4"
                                        1/2"
                                        3/4"
                                        1"
                                        1 1/2"
                                        2" or >
                                        .007-.015
                                        "
                                        "
                                        .015-.025
                                        "
                                        .020-.050
                                        "
                                        "
                                        Fluorosint?500
                                        Fluorosint?207
                                        1
                                        1
                                        .150?br> .025? 350-500
                                        500-600
                                        .010-.015
                                        .003-.008
                                        1/16"
                                        1/8"
                                        1/4"
                                        1/2"
                                        3/4"
                                        1"
                                        1 1/2"
                                        2" or >
                                        .007-.015
                                        "
                                        "
                                        .015-.025
                                        "
                                        .020-.050
                                        "
                                        "
                                        PEEK? unfilled
                                        PEEK 30% GF
                                        PEEK 30% CF
                                        5
                                        7
                                        7
                                        .150?br> .025? 600-1000
                                        600-700
                                        .010-.016
                                        .004-.007
                                        1/16"
                                        1/8"
                                        1/4"
                                        1/2"
                                        3/4"
                                        1"
                                        1 1/2"
                                        2" or >
                                        .002-.005
                                        "
                                        "
                                        .004-.008
                                        "
                                        .008-.012
                                        "
                                        "
                                        Ertalyte?PET-P
                                        Ertalyte?TX
                                        Hydex?4101 PBT-P
                                          .150?br> .025? 500-600
                                        600-700
                                        .010-.015
                                        .004-.007
                                        1/16"
                                        1/8"
                                        1/4"
                                        1/2"
                                        3/4"
                                        1"
                                        1 1/2"
                                        2" or >
                                        .002-.005
                                        "
                                        "
                                        .015-.025
                                        "
                                        .020-.050
                                        "
                                        "
                                        Techtron?PPS
                                        Ryton?PPS
                                        Ryton?BG PPS
                                          .150?br> .025? 100-300
                                        250-500
                                        .010-.020
                                        .005-.010
                                        1/16"
                                        1/8"
                                        1/4"
                                        1/2"
                                        3/4"
                                        1"
                                        1 1/2"
                                        2" or >
                                        .007-.015
                                        "
                                        "
                                        .015-.025
                                        "
                                        .020-.050
                                        "
                                        "
                                        Torlon?4203 PAI
                                        Torlon?4301 PAI
                                        Torlon?4501 PAI
                                        Torlon?4503 PAI
                                        Torlon?4540 PAI
                                        Torlon?5530 PAI
                                        Duratron?XP
                                        Vespel?PI
                                          .025? 300-800 .004-.025
                                         
                                        1/16"
                                        1/8"
                                        1/4"
                                        1/2"
                                        3/4"
                                        1"
                                        1 1/2"
                                        2" or >
                                        .007-.015
                                        "
                                        "
                                        .015-.025
                                        "
                                        .020-.050
                                        "
                                        "
                                        Celazole?PBI   .150?br> .025? 100-150
                                        150-225
                                        .005-.010
                                        .002-.006
                                        1/16" to 1/4"
                                        1/2" or >
                                        .005-.015
                                        .015-.025

                                        Back to Top of Page

                                         
                                        FABRICATION GUIDELINES - MILLING
                                        MATERIALS End Milling / Slotting Face Milling
                                        (C-2) Carbide Tool
                                        high speed
                                        steel (m2,M7)
                                        Depth
                                        of cut
                                        Speed,
                                        ft./min.
                                        Feet,
                                        in./tooth
                                        Depth
                                        of cut
                                        Speed,
                                        ft./min.
                                        Feet,
                                        in./tooth
                                        Acetal copolymer
                                        Delrin 150, Delrin AF
                                        Delrin AF Blend
                                        Nylon 101
                                        Nylatron?GS Nylon
                                        Nylatron?GSM,
                                        Nylatron?GSM Blue,
                                        Nylatron?NSM
                                        MC?901 Nylon,
                                        MC?907 Nylon
                                        1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.150
                                        0.060
                                        1300-1500
                                        1500-2000
                                        0.020
                                        0.005
                                        Polycarbonate
                                        Polysulfone
                                        Ultem?1000 PEI
                                        Ultem?2300 PEI
                                        1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.150
                                        0.060
                                        1300-1500
                                        1500-2000
                                        0.020
                                        0.005
                                        PEEK?/font> 1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.150
                                        0.060
                                        500-750
                                        "
                                        0.020
                                        0.005
                                        Fluorosint?500
                                        Fluorosint?207
                                        1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.150
                                        0.060
                                        500-700
                                        550-750
                                        0.010
                                        0.005
                                        Techtron?PPS
                                        Ryton?PPS
                                        1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.150
                                        0.060
                                        1300-1500
                                        1500-2000
                                        0.020
                                        0.005
                                        Torlon?PAI 1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.035 500-800 .006-.035
                                        Ertalyte?PET-P
                                        Ertalyte?TX
                                        Hydex?4101 PBT-P
                                        1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .250
                                        "
                                        "
                                        "
                                        .050
                                        "
                                        "
                                        270-450
                                        "
                                        "
                                        "
                                        300-500
                                        "
                                        "
                                        0.002
                                        0.003
                                        0.005
                                        0.008
                                        0.001
                                        0.002
                                        0.004
                                        0.150
                                        0.060
                                        1300-1500
                                        1500-2000
                                        0.020
                                        0.005
                                        Duratron?XP
                                        Vespel?PI
                                        Celazole?PBI
                                        1/4"
                                        1/2"
                                        3/4"
                                        1", 2"
                                        1/4"
                                        1/2"
                                        3/4"
                                        .50



                                        .015
                                        450-650
                                        "
                                        "
                                        "
                                        250-350
                                        "
                                        "
                                        0.005



                                        0.002
                                        0.050



                                        0.015
                                        450-650



                                        250-350
                                        0.005-.010



                                        .002-.006

                                        Back to Top of Page

                                         
                                        FABRICATION GUIDELINES - SAWING
                                        MATERIALS Sawing
                                        Material
                                        thickness
                                        Tooth
                                        form
                                        Pitch
                                        teeth/in.
                                        Band Speeds
                                        ft./min.
                                        Acetal copolymer
                                        Delrin 150,
                                        Delrin AF
                                        Delrin AF Blend
                                        Nylon 101
                                        Nylatron?GS Nylon
                                        Nylatron?GSM,
                                        Nylatron?GSM Blue,
                                        MC?901 Nylon,
                                        MC?907 Nylon
                                        <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        10-14
                                        6
                                        3
                                        "
                                        3,000
                                        2,500
                                        2,000
                                        1,500
                                        Polycarbonate
                                        Polysulfone
                                        Ultem?1000 PEI
                                        Ultem?2300 PEI
                                        <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        10-14
                                        6
                                        3
                                        "
                                        4,000
                                        3,500
                                        3,000
                                        2,500
                                        PEEK?/font> <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        8-14
                                        6-8
                                        3
                                        "
                                        4,000
                                        3,500
                                        3,000
                                        2,500
                                        Fluorosint?500
                                        Fluorosint?207
                                        <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        8-14
                                        6-8
                                        3
                                        "
                                        3,000
                                        2,500
                                        2,000
                                        1,500
                                        Techtron?PPS
                                        Ryton?PPS
                                        <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        8-14
                                        6-8
                                        3
                                        "
                                        5,000
                                        4,300
                                        3,500
                                        3,000
                                        Torlon?PAI <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        8-14
                                        6-8
                                        3
                                        "
                                        5,000
                                        4,300
                                        3,500
                                        3,000
                                        Ertalyte?PET-P
                                        Ertalyte?TX
                                        Hydex?4101 PBT-P
                                        <1/2"
                                        1/2"-1"
                                        1"-3"
                                        3"
                                        Precision
                                        "
                                        Butress
                                        "
                                        10-14
                                        6
                                        3
                                        "
                                        5,000
                                        4,300
                                        3,500
                                        3,000
                                        Duratron? XP
                                        Vespel?PI
                                        Celazole?PBI
                                        3/8"-1"
                                        1"-2"
                                        Precision
                                        "
                                        Butress
                                        "
                                        10
                                        10
                                        3,000
                                        1,500

                                        Back to Top of Page

                                         
                                        TROUBLESHOOTING QUICK REFERENCE
                                        Drilling
                                        Difficulty Common Cause
                                        Tapered hole 1. Incorrectly sharpened drill
                                        2. Insufficient clearance
                                        3. Feed too heavy
                                        Burnt or melted surface 1. Wrong type drill

                                        2. Incorrectly sharpened drill
                                        3. Feed too light
                                        4. Dull drill
                                        5. Web too thick
                                        Chipping of surfaces 1. Feed too heavy
                                        2. Clearance too great
                                        3. Too much rake (thin web as described)
                                        Chatter 1. Too much clearance
                                        2. Feed too light
                                        3. Drill overhang too great
                                        4. Too much rake (thin web as described)
                                        Feed marks or spiral lines on inside diameter 1. Feed too heavy
                                        2. Drill not centered
                                        3. Drill ground off-center
                                        Oversize holes 1. Web too thick
                                        2. Insufficient clearance
                                        3. Feed rate too heavy
                                        4. Point angle too great
                                        Undersize holes 1. Dull drill
                                        2. Too much clearance
                                        3. Point angle too small
                                        Holes not concentric 1. Feed too heavy
                                        2. Spindle speed too slow
                                        3. Drill enters next piece too far
                                        4. Cut-off tool leaves nib, which deflects drill
                                        5. Web too thick
                                        6. Drill speed too heavy at start
                                        7. Drill not mounted on center
                                        8. Drill not sharpened correctly
                                        Burr at cut-off 1. Dull cut-off tool
                                        2. Drill does not pass completely through piece
                                        Rapid dulling of drill 1. Feed too light
                                        2. Spindle speed too fast
                                        3. Insufficient lubrication from coolant
                                        Cutting Off
                                        Melted surface 1. Dull tool
                                        2. Insufficient side clearance
                                        3. Insufficient coolant supply
                                        Rough finish 1. Feed too heavy
                                        2. Tool improperly sharpened
                                        3. Cutting edge not honed
                                        Spiral marks 1. Tool rubs during its retreat
                                        2. Burr on point of tool
                                        Concave or convex surfaces 1. Point angle too great
                                        2. Tool not perpendicular to spindle
                                        3. Tool deflecting (use negative rake)
                                        4. Feed too heavy
                                        5. Tool mounted above or below center
                                        Nibs or burrs at cut-off point 1. Point angle not great enough
                                        2. Tool dull or not honed
                                        3. Feed too heavy
                                        Burrs on outside diameter 1. No chamfer before cut-off
                                        2. Dull tool
                                        Turning & Boring
                                        Melted surface 1. Tool dull or heel rubbing
                                        2. Insufficient side clearance
                                        3. Feed rate too slow
                                        4. Spindle speed too fast
                                        Rough finish 1. Feed too heavy
                                        2. Incorrect clearance angles
                                        3. Sharp point on tool (slight nose radius required)
                                        4. Tool not mounted on center
                                        Burrs at edge of cut 1. No chamfer provided at sharp corners
                                        2. Dull tool
                                        3. Insufficient side clearance
                                        4. Lead angle not provided on tool
                                        (tool should ease out of cut gradually, not suddenly)
                                        Cracking or chipping of corners 1. Too much positive rake on tool
                                        2. Tool not eased into cut (tool suddenly hits work)
                                        3. Dull tool
                                        4. Tool mounted below center
                                        5. Sharp point on tool (slight nose radius required)
                                        Chatter 1. Too much nose radius on tool
                                        2. Tool not mounted solidly
                                        3. Material not supported properly
                                        4. Width of cut too wide (use 2 cuts)
                                         

                                        Also see: Guidelines for Machining Ensinger Engineering Plastics
                                         

                                        Trademark Acknowledgments:

                                        RADEL and TORLON are registered trademarks of Solvay Advanced Polymers.
                                        RYTON is a registered trademark of Chevron Phillips Chemical Company.
                                        DELRIN and VESPEL are registered trademarks of DuPont.
                                        ULTEM is a registered trademark of General Electric Company.
                                        CELAZOLE is a registered trademark of Celanese Advanced Materials, Inc.
                                        HYDEX is a registered trademark of A.L. Hyde Company.
                                        DURATRON, ERTALYTE, NYLATRON, and TECHTRON are registered trademarks of Quadrant DSM Engineering Plastic Products.
                                        PEEK is a trademark of Victrex plc.

                                        The information on this page originally provided by Quadrant DSM Engineering Plastics.
                                        Other stock shape manufacturers have also provided relevant information.

                                         



                                        Return
                                        To MAIN

                                        Site
                                        Map
                                        Search
                                        Me
                                        Return To
                                        Linecard
                                        Sales
                                        Terms
                                        Contact
                                        Me

                                                                              city

                                                                              Foreign exchange

                                                                              image

                                                                              city

                                                                              Premier League

                                                                              video

                                                                              reading

                                                                              constellation

                                                                              car