Sure Grip Marine Grade Polymer Sheet
SKIP TO PRICES
KING STARBOARD?/sup>AS is a unique,
superior marine grade polymer material specifically designed for high traffic
areas. This unique product combines the strength, versatility and durability of
King StarBoard?/sup> with a special high-friction, polymer surface.
Click here to view our new brochure
in PDF format.
Click the picture for a larger view of the material.
KING
STARBOARD?/sup>AS
is environmentally stabilized to resist harsh sun and sea conditions,
including ultraviolet light. The surface layer has a dot pattern texture that
inhibits slippage and promotes water drainage.
"The dot pattern texture promotes water drainage."
"A single uniform sheet that does not rot or delaminate."
Applications
Ladder Treads, Bilge Floor Grate, Swim Platform, Flooring
?Dot pattern on one side.
?Fabricate with standard tools.
?Never needs maintenance.
?Unlimited custom/proprietary colors.
?Accents or matches gel coat.
?Made to last the lifetime of the boat.
?Will not rot, swell, or delaminate when exposed to moisture.
It is not a laminated surface, but instead it is a single homogeneous polymer
sheet that will not rot or delaminate.
KING STARBOARD?/sup>AS
comes in eight standard colors.
KING STARBOARD?/sup>AS is ideal for
replacing teak, laminates and inferior plastic products on fishing boats,
recreational boats, pontoon boats and yachts.
Fabrication with KING STARBOARD?/sup>AS
is done with standard woodworking tools.
Our testing shows that these set ups work best with
KING STARBOARD?/sup>AS
Cutting:
These tests were run on 3/4" material. All cuts were performed with the dot
side up. Downcut tools and compression tools were also tested but tended to
cause excessive melting in deep cuts using smaller diameter tools.
1/2" Diameter Tool using a climb cut at 150 IPM 18,000 RPM
Cutting Edge Diameter: 1/2
Cutting Edge Length.: 1-1/8
Shank Diameter: 1/2
Over All Length: 3-1/2
Tool Material: Solid Carbide
Helix: Up
Flutes: 3
Rotation: RH
This router bit can be purchased from
http://www.onsrud.com part number 60-249
3/8" Diameter Tool using a climb cut at 200 IPM 18,000 RPM
Cutting Edge Diameter: 3/8
Cutting Edge Length: 1-1/8
Shank Diameter: 3/8
Over All Length: 3
Tool Material: Solid Carbide
Helix: Up
Flutes: 1
Rotation: RH
This router bit can be purchased from
http://www.onsrud.com part number 63-783.
Engraving:
The sample used was for 1/4" cutting channels wide and 1/16" deep into the
material.
The best results we achieved were using a router bit with these dimensions:
Cutting Edge Diameter: 3/16
Cutting Edge Length: 5/8
Shank Diameter: 1/4
Over All Length: 2
Tool Material: Solid Carbide
Helix: Down
Flutes: 1
Rotation: RH
Feed at 120 ipm was very good with the 3/16" diameter tool working a 1/4"
wide channel in a climb cut direction.
This router bit can be purchased from
http://www.onsrud.com part number 62-718
To create a crisp edge with a saw, use 1800 RPMs at 150" per minute and a
good carbide blade that has 50-75 teeth.
Cleaning
King StarBoard?is very chemically resistant and most common detergents and
cleaners work well. You can use a nylon scrubby?or stiff bristle nylon brush
but care should be taken because excessive force can mar the finish.
Bleach can be applied and allowed to soak to help lift persistent stains.
Pressure washing is also an acceptable method of cleaning. To clean a petroleum
problem such as grease or oil, use citrus cleaner, alcohol, or mineral spirits.
Care must be taken to avoid contact with pencil lead or prolonged contact with
teak oil and other oil based products as these do not clean well and may cause
staining.
Furniture polish or products such as Armor-All?can add an attractive luster
to the finish and hide small mars on the product's surface.
*Do not use polishing products on stepping surfaces to prevent the danger of
slipping.
